Mobile in Water

na phone ivvala morning water lo padindhi...chala badha em cheyalo teliyadu mottam vidadisi endalo pettanu dealer daggariki vellali em avutundho choodali ...browse chestey ee kinda tips kanipinchayi useful ani ikkada post chestunna...

Precautions

Get it out of the water as soon as possible. The plastic covers on cell phones are fairly tight, but water can enter the phone in a short period of time, perhaps only 20 seconds or less. So grab your phone quickly! If you can't get to it in time, your best bet is to remove the battery while it is still under water. Water helps dissipate heat from shorts that can damage the phone, so most damage occurs when the inside of the phone is merely wet and there is a power source.

Don't Panic. Your phone will probably not be too damaged if you right away take it out of the water. While it's in the water, immediately take it out.

Remove the battery. This is one of the most important steps. Don't take time to think about it; electricity and water do not mix. Cutting power to your phone is a crucial first step in saving it. Many circuits inside the phone will survive immersion in water provided they are not attached to a power source when wet.

If you have a GSM carrier, remove your SIM card. Some or all of your valuable contacts (along with other data) could be stored on your SIM. To some people this could be more worth saving than the phone itself. SIM cards survive water damage well, but some of the following steps are unnecessary i.e. don't heat it. Just pat it dry and leave it aside until you need to connect your phone to your cellular network. (This step does not apply to CDMA carriers such as Verizon, Alltel, US Cellular, Sprint, etc.)

Dry your phone. Obviously you need to remove as much of the water as soon as possible, so you can save it from getting into the phone. Shake it out without dropping it, then use a towel or paper towel (ideally trying not to clog the wet paper in the gaps and grooves of the phone) to gently remove as much of the remaining water as possible. Dry the excess moisture by hand.

Remove any covers and external connectors to open up as many gaps, slots, and crevices in the phone as possible.

Use a vacuum cleaner if possible. Do not use a hair dryer (even on a "cold" mode) to dry out the phone, as this may force moisture further into the small components, deep inside the phone. If moisture is driven deeper inside, corrosion and oxidation may result when minerals from liquids are deposited on the circuitry. Using a hairdryer might be a temporary fix, but this will eventually cause component failure inside the phone. Instead, remove all residual moisture by drawing it away with a vacuum cleaner held over the affected areas for up to 20 minutes in each accessible area. This is the fastest method and can completely dry out your phone and get it working in thirty minutes. Be careful not to hold the vacuum too close to the phone, as a vacuum can create static electricity, which is even worse.

Use a substance with a high affinity for water to help draw out moisture. Leave the phone in a bowl or bag of uncooked rice overnight. The rice would absorb any remaining moisture. If available, it is preferable to use desiccant instead.

Desiccant will absorb moisture better than rice. It may be found under a brand name such as the "BHEESTIE Bag™" "DRY-ALL" "Damp Rid" or "Dry Right".

Let the phone sit on absorbent towels, napkin, or other paper. Remember that the goal is to evacuate all the moisture and humidity, not to trap it or add even more.

Check the absorbent material every hour for 4 to 6 hours. If moisture is evident, repeat the vacuuming step and desiccant steps.

Test your phone. After you have waited a day or so, make sure everything is clean and dry looking and re-attach the battery to the phone and see if it works. If your phone does not work, try plugging it into its charger without the battery, if this works, you need a new battery. If not, try taking your cell phone to an authorized dealer. Sometimes they can fix it. Don't try to hide the fact that it has been wet. There are internal indicators that prove moisture.

Take the phone apart If your phone doesn't turn on at all. Try taking it apart. First, make sure that you have ALL the right parts and know exactly where they go. Be sure to put everything back in its proper place once finished. As you're disassembling it, pat each individual part dry with a small towel and use the vacuum cleaner once more on the crevices. If this doesn't work go to the professionals.

Warnings

Do not switch the phone on. This is important as it will prevent a charge from running from the battery to the phone which may subsequently cause the phone to short circuit.

Don't heat the battery or it could leak or explode. Lithium-ion batteries are sensitive. If you use an oven or hairdryer, make sure to remove the battery first.

If you use alcohol make sure to do so outside, and do not apply heat in any form, not even the gentle heat of a monitor. Do not hook up the battery until the alcohol smell dissipates.

Do not apply too much heat to your phone, as mentioned above. You don't want to melt or burn your phone.

Be warned that manufacturers of most modern cell phones place liquid damage indicator stickers that will change colors in the presence of a liquid inside their phones. This helps technicians know that you have dropped your phone in water, as most cell phone insurance coverage policies don't cover water damage. Chances are, if the sticker under the battery is triggered, then the internal stickers you can't access have probably been tripped as well. This will result in you paying a voided-warranty fee in the long run. You should be aware that warranties don't cover water damage, only insurance does, and even then, not all insurance companies or plans will honor water damaged phones. It is also worth noting that these liquid damage indicator stickers have been known to change colors in extreme humidity as well.

Even if all these steps are followed, minerals dissolved in the water can precipitate on solder and component pins, causing corrosion or shorting. Component pins are packed so closely together in modern cell phones that even a small encrustation can create a short, rendering the phone inoperable.

Do not put the phone (or any electronic or metal-containing object) into the microwave. You will destroy electronic components and potentially the microwave.

For the semi-mechanically inclined remove screws and as a minimum crack the case open to allow moisture to escape. Cell phones are normally somewhat water proof so they can be used in the light rain and humid environments. This means that once moisture has entered the phone it is very hard for it to dry out.

Removing your cell phone from the water quickly and IMMEDIATELY REMOVING THE BATTERY gives you the best chance of saving your phone.

If you do not want your cell phone to be damaged, keep it away as far as possible to any liquids.